Fluid-components-international FS10 Button Setup Quick Guide Manuel d'utilisateur télécharger pdf

Fluid Components International LLC 06EN003398 Rev. B

FS10 Button Setup Quick Guide

This guide provides a quick reference to ﬁeld set-up of the trip point and span of the FS10A ﬂow monitor on units not pre-calibrated at the factory to

speciﬁc application parameters. The available PC or command line interface through the RS232 provides the most comprehensive means of setting

up the FS10A ﬂow monitor (refer to operating manual for complete instructions). If that is not feasible, the buttons with LED feedback provide access

to all required functions for ﬁeld set-up.

FS10 Button Controls

General Control Description

The FS10 control “functions” can be accessed through the two buttons by:

1. Entering “function selection”

2. Selecting the desired function to adjust

3. Adjusting the function control

4. Exiting to normal operation

1. To Enter “Function Selection” mode:

a. Press and hold both buttons down for 3 seconds

b. When “function selection” is entered, all the LEDs will ﬂash “on”, then

c. The ﬁrst function (LED # 1) will be illuminated

2. “Function Selection” mode:

Once the unit is in “function selection” mode, the buttons take on new controls:

• The “-“ and “+” buttons will step (increment down or up respectively) through the different functions. The current function number will be

indicated on the LED blinking at the slow rate.

• Holding either the “+” or “-“ for 3 seconds will “select” the current function to be adjusted.

3. When a Function has been selected for adjustment:

After selecting the desired function by pushing and holding either the “-” or “+” button for 3 seconds the LEDs will ﬂash at a faster rate. The

pattern of the LEDs will either reﬂect the current value of the parameter being adjusted, or the “ready to capture” pattern for parameters to be

captured (see speciﬁc function descriptions for details).

The buttons will either increment or decrement the function parameter, or capture a value for the corresponding parameter.

4. To exit out of the current function, push and hold both buttons down for 3 seconds. The LEDs will indicate that you are once again in “function

election” mode, and the current mode will have incremented to the next function. To exit completely (into operational mode), press the two

buttons simultaneously for 3 seconds once again.

Note: Function #4 (load a bank) and function #15 (save to a bank), requires holding either button for 3 seconds to load or save.

Holding both buttons will exit either function without performing the operation.

Button Operation

1 Enter “function selection” Push and hold both buttons simultaneously 3 seconds

2 Select desired “function” Push “+” or “-“ to step through (LEDs indicate function #)

3a. Enter “function adjust” Push and hold either “-“ or “+” button 3 seconds

3b. Adjust within function Follow instructions for particular function entry

4a. Exit “function adjust” Push and hold either “-” or “+” button 3 seconds (now in “function selection” opera-

tion)

[NOTE: Function #4 or #15 requires holding both buttons to exit into function select

operation]

4b. Exit “function selection” Push and hold both buttons simultaneously 3 seconds (now in normal operation)

1 2 3 4

Résumé du contenu

Page 1 - FS10 Button Setup Quick Guide

Fluid Components International LLC 06EN003398 Rev. BFS10 Button Setup Quick GuideThis guide provides a quick reference to ﬁeld set-up of the trip poi

Page 2 - Bank Default Values

Fluid Components International LLC 06EN003398 Rev. BBank Selection of Stored ParametersThe FS10A has 7 storage banks. Banks 1-6 are factory set defa

Page 3 - Button Controls

06EN003398 Rev. B Fluid Components International LLCButton Controls0 = LED off, 1 = LED onFunction # FunctionNameLED Pattern ParameterLED Pattern for

Page 4 - Notice of Proprietary Rights

Fluid Components International LLC 06EN003398 Rev. B9Maximum Hysteresis Value1111111110- +RELAY_HYSTERESIS1 – indicates current value

Commentaires sur ces manuels

Pas de commentaire

Fluid-components-international FS10 Button Setup Quick Guide Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Fluid-components-international FS10 Button Setup Quick Guide. Fluid Components International FS10 Button Setup Quick Guide User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Fluid-components-international FS10 Button Setup Quick Guide